Zone Controller with Universal Telephone InterfaceUTI312 ModelInstallation and Use Manual© 2005 Bogen Communications, Inc.All rights reserved.Specific
10Override InputThe Override is a feature that lets the caller take priority over all other paging functions and make a page.The center two conductors
Other ConnectionsNight Ringer ContactIn addition to 90V ring activation of the Night Ring feature, a contacttriggered feature is also available.The ni
12ZX3 Module ConnectionsZX3 Module Paging Output ConnectionsThere are three zone paging outputs on the ZX3 module. The pagingoutputs are intended to c
13ControlsPaging LevelThe ZX3 module has controls for adjusting the audio level of each zoneindependently.These serve as master level controls that al
14Features & OperationZonesThe UTI312 offers up to twelve zones of paging.These zones are numbered 01 through 12 by default and do notrequire any
15Auto Select Zone GroupAuto Select provides paging to a programmed zone group when the unit is accessed without having to enter anyDTMF keys.This fea
16Code Call Zone Group & TonesBy default, the Code Call zone group is programmed to include all zones.The Code Calling feature gives the callerthe
17Dialing Time-outDialing Time-out can be enabled or disabled and by default is enabled.When enabled, the dialing time-out starts assoon as the unit b
18System ProgrammingSystem programming lets you set certain UTI312 options and tone features using the DTMF keys of a telephone.All programming is acc
19Tone Zone GroupsIn addition to paging zone groups, there are five additional zone groups, each with an associated tonal function.Theseare Override z
© 2004 Bogen Communications, Inc.All Rights Reserved.UL ApprovedNoticeEvery effort was made to ensure that the information in this manualwas complete
20AUX Relay ContactThe UTI312 allows the installer to program a number of different parameters to control the way in which theUTI312 AUX relay contact
21Below are some illustrative examples:Example 1: Emergency Tone/Emergency Announcement BypassThe Tone Trigger 1 and Override inputs are used to prov
22Flexible DialingFlexible Dialing permits the user to custom configure the digit length and the access codes for zones and pagingzone groups.The digi
23Feature Codes & DefaultsFeatureFeatureCodeData DefaultConfirmation ToneConfirmation Tone DisableConfirmation Tone Enable001002002Dialing Time-ou
24FeatureFeatureCodeData DefaultAUX RelayOverride DisableOverride EnableTone Trigger 1 DisableTone Trigger 1 EnableTone Trigger 2 DisableTone Trigger
25Renumber ZoneGroupsZone Group 1Zone Group 2Zone Group 3Zone Group 4Zone Group 5Zone Group 6Zone Group 7Zone Group 8Zone Group 9Zone Group 10Zone Gro
26FeatureFeatureCodeTest Mode(factory use) Test Mode990ResetReset Default 999Setup ToneTurn OnTurn Off000Hang UpNotes to Feature CodesTo clear zones f
27SpecificationsInput Impedance: 600 ohms (nominal)Input Level: -10 dBm (nominal)VOX Sensitivity: -30 dBmBackground Music Input Impedance: 20K ohmsMus
28Block Diagram, UTI312* Ground points marked with an asterisk must not be connected toEarth Ground when GND ST terminal is connected to Earth Ground.
Block Diagram, ZX329* Ground points marked with an asterisk must not be connected toEarth Ground when GND ST terminal is connected to Earth Ground.
Contents3Introduction ...4Voice Channel ...
Limited Warranty30The UTI312 is warranted to be free from defects in material or workmanship for two (2) years from the date of sale to the originalpu
31
50 Spring Street, Ramsey, NJ 07446, U.S.A.Tel. 201-934-8500, Fax: 201-934-9832, www.bogen.com
4IntroductionThe UTI312 Paging System is an expandable multi-zone paging and signaling system.The system provides the followingfeatures and functions:
5Panel DescriptionsUTI312 Callouts1. Ground Start Terminal - Connection for PBX ground. Used only when the ground start interface is selected.2. Earth
InstallationMountingWall MountingMounting to a plywood backboard or studs:1.On each side remove the four screws in the corners and use them toattach t
ZX3 Module Installation & Jumper SelectionsThe UTI312 module bay can accommodate up to four ZX3 modules. EachZX3 module has 3 zone outputs giving
8PBX Loop Start Trunk PortIn this configuration, the unit supplies a 24V talk battery and loop current detection.When the unit detects a loopresistanc
9Trunk DisconnectThe UTI312 includes a Trunk Disconnect feature. The purpose of the Trunk Disconnect feature is to release theUTI312 from the trunk po
Comments to this Manuals